EXACTLY HOW TO REMOVE AND CHANGE A BATHTUB

Exactly How to Remove and Change a Bathtub

Exactly How to Remove and Change a Bathtub

Blog Article

Visit The Following Page

Do you find yourself trying to find critical info concerning Tools You Need to Install a New Bathtub ?


How to Install a Bathtub Yourself
Installing a tub isn't exactly rocket science, but it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately hard task. If the old tub is conveniently accessible, the job can relocate quickly; if you have to open a wall surface to eliminate the old bathtub and position the brand-new tub, the job is much harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to move out the old tub and also embeded in the new one. Ensure you have actually certified yourself for the task and also fit attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one prior to you begin. Opportunities are you might require a professional plumber to make tube connections.
This post will certainly aid you mount a new bathtub in your restroom if you have already gotten a brand-new bathtub and also don't require to transform the setup of your previous water supply pipelines.
Your devices and also product list should comprise the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Setup


    To start with, the supporting framework supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop pressure on the tub.
    Fit the versatile tap connectors to the bottom of both taps utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the provided washers.
    Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last placement.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be quite bothersome because of the restricted accessibility that is commonly the situation.
    Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a fabric ready for the continuing to be water that will certainly come from the pipelines. When the supply pipes have actually been removed, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single faucets from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
    Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Utilizing both wood boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
    The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the level and adjusting the feet on the tub up until the level reviews degree.
    To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the exact same for the other tap.
    Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Fill up the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
    Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and sealing around the tub needs to wait till the bath tub has been used at the very least once as this will resolve it right into its final placement.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipelines.
    If you require to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Safeguard the tap in place with the supplier provided backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former kind must be attached to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.

    Tiling Around the Bath tub


    In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and possible leaks to the ceiling below.
    You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can crack fairly early if you do not consider this movement prior to securing.
    Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is advisable to fit the tiles using waterproof or water-proof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you enjoy more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a remark down the page. We will be delighted to see your insights about this blog post. We hope that you visit us again in the future. Appreciated our post? Please share it. Let others locate it. Thank you so much for going through it.




    Schedule Your Service


    Report this page